RCA Video Game Headset WHR120RS User Guide

H E A D P H O N E S  
STEREO INFRARED  
HEADPHO NE  
W ITH FLAT TRANSM ITTER  
Thank you for choosing RCA Wireless Headphones. You have selected  
a
fine product designed to provide years of performance. Before  
attempting to use your Wireless Headphones, please remove all parts  
from the box and read the installation and use instructions carefully.  
Lim ite d 1 Ye a r Wa rra n ty  
W HR1 2 0 RS  
 
EXPLANATION OF CONTROLS  
ON THE IR STEREO TRANSMITTER (see figure 1 below)  
1. IR transmitting LEDs,to transmit the audio signal to the IR  
headphone  
2. Power on/ off switch  
3. DC input connector, to power the IR transmitter  
4. Recharge cable, to charge the batteries of IR headphone  
5. Input stereo audio signal cable with 3.5 mm jack connector  
(FRONT)  
1
3
2
(BACK)  
5
Figure 1  
4
ON THE STEREO HEADPHONE RECEIVER (see figure 2 below)  
6. Power on/ off LED indicator  
7. Volume control  
8. Power on/ off switch  
9. IR sensors, to receive IR signals from the transmittes  
10. Recharge cable input socket to recharge the batteries of  
the IR headphone  
11. Charge LED indicator  
9
6
8
RIGHT  
LEFT  
7
10  
11  
DFoiwgnuloraed 2from Www.Somanuals.com. All Manuals Search And Download.  
33  
INSTALLATION  
1. Connect the audio signal cable located on the back of the  
transmitter to the headphone jack of your audio source. This  
headphone jack is located on the front panel of most TVs and  
stereo receivers. Insert the plug on the audio signal cable into the  
headphone jack. Use the plug adapter included in this package if  
the jack is the 1/ 4” (6.3 mm) size. If you wish to connect  
directly to the “AUDIO OUTjacks that are standard on most  
equipment, then you must purchase a seprate adapter with the  
phono plugs at your local dealer.  
AC  
SOCKET  
AUDIO  
CABLE  
DC  
ADAPTER  
TO AUDIO  
SOURCES  
RIGHT  
6.3 mm STEREO  
ADAPTER  
RECHARGE  
CABLE  
3.5 mm STEREO PLUG  
Figure 3  
2. Insert the connector of the AC/ DC adapter into the 12V DC input  
connector on the rear of the IR transmitter (see figure 3 above).  
3. Plug the adapter into a 120 Volt wall outlet.  
4. Remove the soft earpads from the earcups by gently lifting them  
up. They have plastic tabs that hold them in place to the inside of  
the earcup. See figure 4 which illustrates the soft earpads  
separated from the earcup on the headset. Insert the two  
rechargeable batteries (AAA size) into the left and right battery  
compartments, ensuring that the polarity is correct (see figure 4).  
Replace the earpads by snapping them back in place on the  
earcups. The plastic tabs on the soft earpads must be matched  
correctly with the slots in the earcups.  
5. Note: Before using the IR headphone for the first time, please  
ensure that batteries are fully charged (for 16 hours). This will  
guarantee a longer operating life for the batteries.  
 
44  
EARPAD AND  
BATTERY COVER  
AAA SIZE BATTERY  
Figure 4  
OPERATION  
1. Switch on the (IR) transmitter and position it in a location at  
approximately the same height as that of the headphone when  
it will be in use. This system operates using IR light signals  
that are invisible to the human eye. It is important for the per-  
formance of the unit to have the transmitter and headphone at  
about the same height for optimum reception. Placement on top  
of a TV or bookshelf at a height of approximately 4 feet should  
be sufficient.  
2. Make certain that there are no obstructions that may block the  
IR signals that are emitted from the translucent plastic window  
on the front of the transmitter. The headphone must receive  
these signals clearly for best performance.  
3. Slide the switch on the headphone to “ON.  
4. Before placing the headphone over your ears, listen to the  
volume from the earcups to make certain that the volume is not  
too loud before placing the unit on your head (see page 2).  
Adjust the volume as needed with the volume control thumb  
wheel located on the “RIGHTearcup. Once the volume level is  
at a comfortable setting, place the headphones over your ears  
and adjust the volume as desired.  
 
55  
RECHARGING  
1. Switch off the power of the headphone before charging.  
2. Note: Before using the IR headphone for the first time, please  
ensure that the batteries are fully charged (for 16 hours). This  
will guarantee a longer operating life for the batteries.  
3. Connect the recharge cable located on the back of the  
transmitter into the charge input of the headphone.  
4. The charge indication Green LED on the headphone will light  
to indicate that the batteries are charging.  
5. The batteries are fully charged after charging for at least 16  
hours. Do not charge the batteries longer than 24 hours as  
this  
nect  
will reduce battery performance. After charging, discon-  
the headphone from the recharge cable.  
POSITIONING OF IR TRANSMITTER  
1. Place the transmitter unit so that the front of the IR transmitter  
approximately faces the center of your listening area (see  
figure 5 on page 7).  
2. Because IR light travels in a straight line, place the transmitter  
at the same height, or slightly higher than the reception height,  
of the headphone.  
3. High IR light content such as sunlight and bright indoor lighting  
may degrade the audio signal and cause interference. If you  
experience such problems, simply move the system to a darker  
area away from the source of the bright light.  
 
66  
IR TRANSMITTER  
OPTIMUM  
LISTENING RANGE  
35°  
35°  
HEADPHONES  
25 FT.  
RANGE OF  
TRANSMITTER  
Figure 5  
 
77  
SPECIFICATIONS  
System  
Carrier frequency  
:
:
Infrared (IR)  
Left channel 2.3 MHz  
Right channel 2.8 MHz  
FM  
200mA, 12V DC  
2 X AAA rechargeable batteries  
40 - 12,000 Hz  
50 dB  
Modulation  
:
:
:
:
:
:
:
Power supply transmitter  
Power supply headphone  
Frequency response  
S/ N ratio  
Distortion  
Channel separation  
1% THD  
40 dB  
LIMITED 1 YEAR WARRANTY  
Thomson multimedia Inc. warrants that for 1 year from date of pur-  
chase, it will replace this product if found to be defective in materi-  
als or workmanship. Return it postage prepaid to the Product  
Exchange Center address for prompt, no charge replacement with a  
current equivalent. This replacement is Thomson multimedia Inc.s  
sole obligation under this warranty. Thomson multimedia Inc. will  
not be responsible for any incidental or consequential damages, or  
for any loss arising in connection with the use or inability to use this  
product. Some states do not allow the exclusion or limitation of inci-  
dental or consequential damages, so the above limitation or exclu-  
sion may not apply to you. This warranty excludes defects or dam-  
age due to misuse, abuse, or neglect. This warranty gives you spe-  
cific legal rights, and you may also have other rights, which vary  
from state to state.  
© 2001 Thomson multimedia Inc.  
Product Exchange Center  
11721 Alameda Ave.  
Socorro, TX 79927  
PWHR120RSI/ B Rev0501  
Trademark(s) ® Registered  
Marca(s) Registrada(s)  
Made In China  
 
88  

QSC Audio Baby Monitor 522ua User Guide
QSC Audio Portable Speaker SC 424 User Guide
Radio Shack Headphones 33 1185 User Guide
Radio Shack Universal Remote 15 2107 User Guide
RCA VCR VR628HF User Guide
Ryobi Saw 4060310 User Guide
Samsung Camera Lens D XENOGON 35 User Guide
Sanyo Car Stereo System DC DAB03 User Guide
Sears Lawn Mower 33731 User Guide
Sennheiser Battery Charger L 2021 40 User Guide