R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1--800--554--6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
WT200
IMPORTANT MANUAL -- Do not throw away
MANUAL IMPORTANTE -- No lo descarte
MANUEL IMPORTANT -- À Conserver
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
Electrolux Home Products
104 Warren Road
Augusta, GA 30907
Copyright E2004 Electrolux Home Products, Inc.
530163808
2/2/04
disconnected. Keep vents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
D Never place any object in the air intake open-
ing as this could restrict proper air flow and
cause damage to the unit.
D Never use for spreading chemicals, fertiliz-
ers, orother substances which may contain
toxic materials.
SPECIAL NOTICE: Exposure to vibra-
tions through prolongeduse of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weatherhas beenlinked toblood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An antivibration system
does not guarantee the avoidance of these
problems. Users who operatepower tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
D To avoid spreadingfire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
D Use only for jobs explained in this manual.
MAINTAIN YOUR UNIT PROPERLY
D Have all maintenance other than the rec-
ommended procedures described in the in-
struction manual performed by an autho-
rized service dealer.
D Disconnect spark plug before performing
maintenance except for carburetor adjust-
ments.
D Use only recommended PoulanŽ replace-
ment parts; use of any other parts may void
your warranty and cause damage to your
unit.
D Empty fuel tank before storing the unit. Use
up fuel left in carburetor by starting engine and
letting it run until it stops.
D Do not use any accessory or attachment
other than those recommended by manufac-
turer for use with your unit.
SPECIAL NOTICE:For users on U.S. For-
est Land and in some states, including Cali-
fornia (Public Resources Codes 4442 and
4443),Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington: Certain internal
combustion engines operated on forest,
brush,and/orgrass coveredlandin theabove
areas are required to be equipped with a
spark arresting screen, maintained in effec-
tive working order, or the engine must be con-
structed, equipped, and maintained for the
prevention of fire. Check with your state or lo-
cal authorities for regulations pertaining to
these requirements. Failure to follow these
requirementsis a violation of thelaw. This unit
is not factory equipped with a spark arresting
screen; however, a spark arresting screen is
available as an optional part. If a spark arrest-
ing screen is required in your area, contact
your authorized service dealer for the correct
kit. Thespark arrestingscreen, blower tubes,
and nozzles must be assembled to unit to be
in full compliance with regulations.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D Store in a dry area out of reach of children.
ASSEMBLY
NOTE: Knob must be loose enough to allow
blower tube to be inserted in blower outlet.
ing counterclockwise.
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
Blower
Blower
Outlet
Tube
Groove
Rib
WARNING: If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
2. Secure the tubeby turningthe knob clock-
wise.
3. To remove thetube, turn the knobcounter-
clockwise to loosen the tube; remove the
tube.
D
A standard screwdriver is required for as-
sembly.
VACUUM BAG ASSEMBLY
BLOWER TUBE ASSEMBLY
1. Align the rib on the blower tube with the
groove in the blower outlet; slide the tube
into place.
1. Open the zipper on the vacuum bag and
insert the elbow tube.
2. Push the small end of the elbow tube
through the small opening in the bag.
-- 3 --
Elbow
Tube
4. Hold the vacuum inlet cover open until up-
per vacuum tube is installed.
Small
Opening
Vacuum Inlet
Zipper
Opening
Retaining Post
Rib
NOTE: Make sureedgeofthesmall opening
is flush against the flared area of the elbow
tube, and the rib on the elbow tube is on the
bottom.
Vacuum
Inlet
Cover
3. Close thezipperonthebag.Make surethe
5. Place the hooks of the upper vacuum tube
on the retaining posts of the unit.
6. Pivot the tube until it is secured to the
zipper is closed completely.
4. Remove blower tube from engine.
blower unit by the vacuum inlet latch.
Rib
PIVOT
Inlet Cover
Latch
Groove
5. Inserttheelbowtube intothebloweroutlet.
Make sure elbow tube rib is aligned with
the blower outlet groove.
6. Turnknobclockwise tosecure elbowtube.
Retaining
Hook
Post
VACUUM TUBE ASSEMBLY
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury.
1. Align the lower vacuum tube as shown.
Push lower vacuum tube into upper vacu-
um tube.
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
1. Remove the vacuum tubes by inserting
the tip of a screwdriver into the latch area
of the vacuum inlet.
2. Gently tilt handle of screwdriver toward
the back of the unit to release the latch
while pulling up on the upper vacuum tube
with your other hand.
Upper Vacuum
Tube
Latch Area
Lower Vacuum Tube
2. Insert the tip of a screwdriver into thelatch
area of the vacuum inlet.
Blower
Outlet
La
A
Latch Area
Vacuum
Inlet Cover
3. Remove the vacuum bag.
4. Close the vacuum inlet cover and make
sure it is latched closed.
5. Reinstall the blower tube (see BLOWER
TUBE ASSEMBLY).
3. Gently tilt the handle of the screwdriver to-
ward the back of the unit to release the
latch while pulling up on the vacuum inlet
cover with your other hand.
-- 4 --
SHOULDER STRAP ADJUSTMENT
1. Hold the unit as shown with the muffler side
facing away from your body and clothes.
2. Pass the shoulder strap over your head
and onto your right shoulder.
3. Extend your left arm toward the rear of the
vacuum bag.
4. Adjust shoulder strap until the vacuum
bag/shoulder strap seam lies between
your thumb and index finger.
5. Make sure air flows freely from the elbow
tube into bag. If bag is kinked, the unit will
not operate properly.
OPERATION
KNOW YOUR BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Upper
Lower
Vacuum Tube
Primer Button
Choke Lever
Vacuum Bag
Fuel Mix
Throttle
Fill Cap
Lever
Starter
Rope
Spark Plug
Elbow Tube
Blower
Tube
Rear
Handle
THROTTLE LEVER
CHOKE LEVER
The THROTTLELEVER is used to select the
desired engine speed and to stop the engine.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After engine attempts to start, move the
choke lever to the HALF CHOKE position.
Once engine starts, move choke lever to the
RUN position.
Movethethrottlelever tothe
full speed operation. Move the throttle lever
to the positionfor idle speed. To stopthe
engine, move the throttle lever to the STOP
position.
positionfor
PRIMER BUTTON
The PRIMER BUTTON removes air from the
carburetor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate primer button
by pressing it and allowing it to return to its origi-
nal position.
-- 5 --
This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good quality
synthetic 2-cycle air-cooled engine oil
designed to be mixed at a ratio of 40:1.
Poulan/Weed Eater brand synthetic oil is
recommended. Mix gasoline and oil at a ratio
of 40:1. A 40:1 ratio is obtained by mixing 3.2
ounces (95 ml) of oil with 1 gallon (4 liters) of
OPERATING POSITION
ye
otec
unleaded gasoline.
DO NOT USE
automotiveoil orboatoil. Theseoils will cause
engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container
momentarily to assure that the fuel is
thoroughlymixed. Always readand follow the
safety rules relating to fuel before fueling your
unit.
Blower
Vacuum
OPERATING TIPS
IMPORTANT
S While vacuuming or blowing debris, hold
the unit with the muffler side facing away
from your body and clothes (see OPERAT-
ING POSITION illustration above).
S To reduce the risk of hearing loss
associated with sound level(s), hearing
protection is required.
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol)can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system ofan enginewhile instorage. Toavoid
engine problems, empty the fuel system
beforestoragefor 30days or longer. Drainthe
gas tank,starttheengine andlet it rununtil the
fuel lines and carburetorareempty. Usefresh
S To reduce the risk of injury associated with
contacting rotating parts, stop the engine be-
fore installing or removing attachments. Do
not operate without guard(s) in place.
S Operate power equipment only at reasonable
hours--not early in the morning or late at night
when people might be disturbed. Comply with
times listed in local ordinances. Usual recom-
mendations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
fuel next season.
Never use engine or
carburetorcleaner products in the fuel tank or
permanent damage may occur.
NOTE: Unit must be placed on its side when
adding fuel (see illustration below).
S To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S Use rakes andbrooms to loosen debris be-
fore blowing.
S In dusty conditions, slightly dampen sur-
faces or use a mister attachment whenwa-
ter is available.
S Conserve water by using power blowers
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S Watchoutfor children, pets, openwindows,
or freshly washed cars. Blow debris away
safely.
S Use the full blower nozzle extension so the
air stream can work close to the ground.
S After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
TO STOP THE ENGINE
D To stop the engine, move the throttle lever
to the STOP position.
BEFORE STARTING ENGINE
BEFORE STARTING THE ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understandthe safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
WARNING: You MUST make sure
the tubes are secure before using the unit.
D
Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
FUELING ENGINE
D
WARNING: Remove fuel cap slowly
when refueling.
-- 6 --
STARTING POSITION
NOTE: If engine attempts to start before the
th
5
pull, go to next step immediately.
5. Move the choke lever to the HALF
CHOKE position.
6. Pull the starter rope sharply until the en-
gine runs, but no more than 5 pulls (below
30_ F, 10 pulls).
7. After a 5 second warm--up, move the
choke lever to the RUN position.
Blower
8. Allow the unit to run for 30 more seconds
at the RUN position before moving the
throttle lever to
position.
If engine has not started after 5 pulls (at HALF
CHOKE), repeat STARTING A COLD ENGINE
procedure. If engine still does not start, proceed
to STARTING A FLOODED ENGINE.
9. To stop the engine, move the throttle lever to
the STOP position.
WARNING: When starting engine,
hold the unit as illustrated. Donot set unit onany
surface except a clean, hard area when starting
engine or while engine is running. Debris such
as gravel, sand, dust, grass, etc. could be
picked up by the air intake and thrown out
through the discharge opening, damaging the
unit or property, or causing serious injury to by-
standers or the operator.
STARTING A WARM ENGINE
NOTE: If fuel tank is empty, add fuel; then,
follow STARTING A COLD ENGINE proce-
dure. Do not fill fuel tank while engine is hot.
STARTING A COLD ENGINE
1. Move throttle lever to the
2. Move choke lever to the FULL CHOKE
position.
3. Slowly press the primer button 8 times.
1. Move throttle lever to the
position.
position.
2. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.
T
3. To stop the engine, move the throttle lever to
the STOP position.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing the
choke lever in the RUN position. Move throttle
lever to the fast position
; then, pull rope
until engine starts. After engine starts, move the
throttle lever to the slow position
engine to idle.
to allow
Starting could require pulling the starter rope
many times depending on how badly the unit is
flooded.
If unit still doesn’t start refer to the TROUBLE-
SHOOTING TABLE or call 1-800-554-6723.
Choke Lever
4. Pull starter rope sharply until engine at-
tempts to run, but nomore than5 pulls (be-
low 30_ F, 8 pulls).
MAINTENANCE
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
WARNING: Avoid touching muffler
unless engine and muffler are cold. A hot
muffler can cause serious burns.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
S Housing Screws
S Muffler
CHECK FOR DAMAGED OR WORN
PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Fuel Tank -- Do not use unit if fuel tank shows
signs of damage or leaks.
GENERAL RECOMMENDATIONS
Thewarrantyonthis unit doesnot cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
S Vacuum Bag -- Do not use vacuum bag if it
is torn or damaged.
-- 7 --
INSPECT AND CLEAN UNIT AND
REPLACE FUEL FILTER
Toreplacefuel filter, drainunit by runningit dry
of fuel, then remove fuel cap/retainer assem-
bly from tank. Pull filter from tank and remove
it from thefuel line. Install new fuel filter onfuel
line; reinstall parts.
DECALS
S After each use, inspect complete unit for
loose or damagedparts. Clean theunit and
decals using a dampcloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
Fuel Line
Fuel Filter
Air Filter
Cover
CHECK MUFFLER MOUNTING
SCREWS
Once each year, ensure muffler mounting
screws are secure and tightened properly to
prevent damage.
Screws
Air Filter
Cleaning the air filter:
Mounting
Screw
Holes
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean or replace
air filter after every 5 hours of operation or
yearly, whichever comes first.
Muffler Cover
1. Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
Screws
NOTE: Donotclean filter in gasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporativeemis-
sions.
1. Loosen and remove the 2 screws from the
muffler cover.
2. Remove the muffler cover.
3. Tighten the 2 muffler mounting screws se-
curely.
4. Reinstall muffler cover and 2 screws.
Tighten securely.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.
6. Replace parts.
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
CARBURETOR ADJUSTMENTS
There is no screw for idle adjustment on your
blower. The throttle lever is used to control
engine speed. The throttle lever can be
placed in one of four positions: STOP, IDLE
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
or
, FULL THROTTLE or
, and one
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
intermittentposition. Ifyour enginewill notrun
properly or you require further assistance,
contact an authorized service dealer or call
1--800--554--6723.
4. Reinstall the spark plug boot.
STORAGE
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Store unit and fuel well out of the reach of
children.
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
-- 8 --
SEASONAL STORAGE
ENGINE
Prepareunit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy stor-
age.
S Remove spark plug and pour 1 teaspoonof
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Clean air filter.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual,see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel
tank or fuel storage container. Follow the mix
instructions found on stabilizer container. Run
engine at least 5 minutes after adding stabilizer.
S
Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having thepropergasolineto
oil ratio.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts torust.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of the
recommended remedies below other than remedies that require operation of the unit.
TROUBLE
Engine will not
start.
CAUSE
1. Engine flooded.
REMEDY
1. See “Starting a Flooded Engine”
in Operation section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Contact an authorized service dealer.
5. Compression low.
1. Fuel not reaching
carburetor.
1. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
Engine will not
idle properly.
2. Carburetor requires
adjustment.
3. Crankshaft seals worn.
4. Compression low.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer
4. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
1. Air filter dirty.
2. Fuel not reaching
carburetor.
Engine will not
accelerate,
lacks power, or
dies under a
load.
3. Clean or replace spark plug
and re-gap.
3. Spark plug fouled.
4. Contact an authorized service dealer.
4. Carburetor requires
adjustment.
5. Carbon build up.
6. Compression low.
5. Contact an authorized service dealer.
6. Contact an authorized service dealer.
1. Choke partially on.
2. Fuel mixture incorrect.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
Engine smokes
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs hot.
1. See “Fueling Engine” in Operation
section.
1. Fuel mixture incorrect.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Contact an authorized service dealer.
4. Carbon build up.
-- 9 --
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
cover predelivery setup or normal adjustments
explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of ELECTROLUX HOME PROD-
UCTS, INC., is to continuously improve its
products. Therefore, ELECTROLUX HOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obliga-
tion to any purchaser.
warrants to the original purchaser that each new
PoulanŽ brand gasoline tool or attachment is
free from defects in material and workmanship
and agrees to repair or replace under this war-
ranty any defective gasoline product or attach-
ment as follows from the original date of pur-
chase:
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Additionally,
this warranty does not cover tune-ups, spark
plugs, filters, starter ropes, starter springs, cut-
ting line, or rotating head parts that will wear and
require replacement with reasonable use during
the warranty period. This warranty does not
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
TIONS: The U. S. Environmental Protection
Agency and ELECTROLUX HOME PROD-
UCTS, INC., are pleased to explain the emis-
sions control system warranty on your year
2002--2004 small off--road engine. ELECTRO-
LUX HOME PRODUCTS, INC., must warrant
the emission control system on your small off--
road engine for the periods of time listed below
provided there has been no abuse, neglect, or
improper maintenance of your small off--road
engine. Your emission control system includes
parts such as the carburetor and the ignition
system. Where a warrantable condition exists,
ELECTROLUX HOME PRODUCTS, INC., will
repair your small off--road engine at no cost to
you. Expenses covered under warranty include
diagnosis, parts and labor. MANUFACTUR-
ER’S WARRANTY COVERAGE: If any emis-
sions related part on your engine (as listed un-
der Emissions Control Warranty Parts List) is
defective or a defect in the materials or work-
manship of the engine causes the failure of such
an emission related part, the part will be repaired
or replaced by ELECTROLUX HOME PROD-
UCTS, INC. OWNER’S WARRANTY RE-
SPONSIBILITIES: As the small off--road en-
gine owner, you are responsible for the perfor-
mance of the required maintenance listed in
your instruction manual. ELECTROLUX HOME
PRODUCTS, INC., recommends that you re-
tain all receipts covering maintenance on your
small off--road engine, but ELECTROLUX
HOME PRODUCTS, INC., cannot deny war-
ranty solely for the lack of receipts or for your
failure to ensure the performance of all sched-
uled maintenance. As the small off--road en-
gine owner, you should be aware that ELEC-
TROLUX HOME PRODUCTS, INC., may deny
you warranty coverage if your small off--road
engine or a part of it has failed due to abuse, ne-
glect, improper maintenance, unapproved mod-
ifications, or the use of parts not made or ap-
proved by the original equipment manufacturer.
You are responsible for presenting your small
off--road engine to an ELECTROLUX HOME
PRODUCTS, INC., authorized repair center as
soon as a problem exists. Warranty repairs
should be completed in a reasonable amount of
time, not to exceed 30 days. If you have any
questions regarding your warranty rights and re-
sponsibilities, you should contact your nearest
authorized service center or call ELECTRO-
LUX HOME PRODUCTS, INC., at
1--800--554--6723.
WARRANTY COM-
MENCEMENT DATE: The warranty period be-
gins on the date the small off--road engine is
purchased. LENGTH OF COVERAGE: This
warranty shall be for a period of two years from
the initial date of purchase. WHAT IS COV-
ERED: REPAIR OR REPLACEMENT OF
PARTS. Repair or replacement of any war-
ranted part will be performed at no charge to the
owner at an approved ELECTROLUX HOME
PRODUCTS, INC., servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
ELECTROLUX HOME PRODUCTS, INC., at
1--800--554--6723.
Any warranted part which is not scheduled for
replacement as required maintenance, or which
WARRANTY PERIOD:
-- 1 0 --
is scheduled only for regular inspection to the ef-
fect of “repair or replace as necessary” shall be
warranted for 2 years. Any warranted part which
is scheduled for replacement as required main-
tenance shall be warranted for the period of time
up to the first scheduled replacement point for
that part. DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to the
determination that a warranted part is defective
if the diagnostic work is performed at an ap-
proved ELECTROLUX HOME PRODUCTS,
INC., servicing center. CONSEQUENTIAL
DAMAGES: ELECTROLUX HOME PROD-
UCTS, INC., may be liable for damages to other
engine components caused by the failure of a
warranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by abuse,
neglect, or improper maintenance are not cov-
ered. ADD-ON OR MODIFIED PARTS: The
use of add--on or modified parts can be grounds
for disallowing a warranty claim. ELECTRO-
LUX HOME PRODUCTS, INC., is not liable to
cover failures of warranted parts caused by the
use of add--on or modified parts. HOW TO FILE
A CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service
center or call ELECTROLUX HOME PROD-
UCTS, INC., at 1--800--554--6723. WHERE TO
GET WARRANTY SERVICE: Warranty ser-
vices or repairs shall be providedat all ELEC-
TROLUX HOME PRODUCTS, INC., service
centers. Call 1--800--554--6723. MAINTE-
NANCE, REPLACEMENT AND REPAIR
OF EMISSION RELATED PARTS: Any
ELECTROLUX HOME PRODUCTS, INC.,
approved replacement part used in the per-
formance of any warranty maintenance or re-
pair on emission relatedparts will beprovided
withoutchargetothe ownerif thepart is under
warranty. EMISSION CONTROL WAR-
RANTY PARTS LIST: Carburetor, Ignition
System: Spark Plug (covered up to mainte-
nance schedule), Ignition Module. MAINTE-
NANCE STATEMENT: The owner is respon-
sible for the performanceof all requiredmain-
tenance as defined in the instruction manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 11 --
|