Quick Use and Hookup Guide
CONTENTS
INSTALLING LCD TV ON THE WALL . .1 TUNER MODE CONTROL . . . . . . . . . . . . . 5
UNFOLD THE BASE. . . . . . . . . . . . . . . 1 AUTO PROGRAM (SETTING UP
TV CHANNEL INSTALLATION . . . . . . . .2 CHANNELS) . . . . . . . . . . . . . . . . . . . . 5
PRESENTATION OF THE LCD TV . . . . . 2 CABLE BOX (WITH RF IN/OUTPUTS) . . 6
ACCESSORIES. . . . . . . . . . . . . . . . . . . .3 CABLE BOX (WITH AUDIO/VIDEO
BATTERY INSTALLATION . . . . . . . . . . . . 3 OUTPUTS) . . . . . . . . . . . . . . . . . . . . . 6
REMOTE CONTROL OPERATION . . . . . .3 S-VIDEO CONNECTIONS . . . . . . . . . . . 7
ANTENNA TV . . . . . . . . . . . . . . . . . . 4 COMPONENT (HD) CONNECTIONS . . .7
BASIC CABLE TV CONNECTION . . . . . 4 PC (MONITOR) INPUTS . . . . . . . . . . . 8
IMPORTANT
NOTE: This quick setup guide is used with several
different LCD TV models. Not all features (and drawings)
discussed in this manual will necessarily match those
found with your LCD TV set. This is normal and does not
require that you contact your dealer or request service.
WARNING:TO PREVENT FIRE OR SHOCK HAZARD
DO NOT EXPOSETHIS UNITTO RAIN OR EXCESSIVE.
INSTALLING LCDTV ON THE WALL
The stand of your LCD TV complies with the VESA standard, if you intend to install the LCD TV on the wall,
please consult a professional technician for proper installing.
Wall Mounting of your LCD TV :
Put your LCD TV set on a safe and flat surface, then
fold the base backward.
Note: To fold the base requires a degree of force.
1
Use for the TV set a Vesa compliant wall mount (not included).
(For 15 inch: 75x75 mm , For 20 inch: 100x100 mm)
2
3
Use for installation by a professional technician.
Note: The manufacture accepts no liability, ensure installation is
done by a professional technician.
UNFOLD THE BASE
Expanding the base requires a degree of force; please use sufficient force to unfold the base.
When unfolding the base, place the TV on a flat, sturdy surface before expanding the base.
Download from Www.Somanuals.com1. All Manuals Search And Download.
3138 155 24011
ACCESSORIES
BATTERY INSTALLATION
When you unpack this unit, make sure it includes the
following:
Remove the battery compartment lid on
the bottom of the remote control.
1
2
Place lithium cell in the remote control.
Be sure the (+) and (-) ends of the
batteries line up as marked inside the
battery (CR2025) compartment.
Reattach the battery
compartment lid.
Power adapter & cable
User's Manual & Quick Use and Hookup Guide
3
1
3
d
r
a
C
y
t
n
a
r
r
r
a
a
W
W
2
Tuner L-Adapter
Warranty Card
REMOTE CONTROL OPERATION
Status/Exit Button-
Power button
Press to turn the LCD TV on or off.
Press to see the current channel number on the
TV screen. Also press to clear the TV menu
after control adjustments.
CC button
Press the CC button to select CC on or CC off.
SAP button
Press to select a sound mode if available with
the TV programming:Mono, Stereo, or SAP.
Sleep button
Press to set the LCD TV to turn itself off within a
certain time.
Incredible Surround button-
Adds greater depth and dimension to TV
sound.
PIP button
Press repeatedly to change the size of PIP window
in PC mode.
Select from Incredible Surround or OFF.
Picture Format button
A/CH Button
Press to go to previously selected channel.
Press the FORMAT button repeatedly to toggle
among the three screen format sizes; 4:3,
EXPAND 4:3, COMPRESS 16:9,
Menu button
Press to activate onscreen menu, back to
previous level inside the onscreen menu or press to
exit the onscreen menu.
Cursor Buttons (Left, Right, Up,
Down)-
Press these buttons to highlight, select, and
adjust items on the TV’s on screen menu.
Channel button
Press to adjust the channel up or down.
Volume button
Press to increase or decrease the sound level.
Mute button
Press to eliminate or restore the LCD TV sound.
Mute will appear on the screen when the sound is
muted.
Number buttons
Press the number buttons for direct access to
the TV channels. For a 3-digit channel, enter
the first digit followed the next 2 digits.
Auto Sound button
Press repeatedly to select among the 4 settings;
Personal, Voice, Music, or Theatre.
AV+ button
Press to select the video input source: PC,
DVI, TV, AV, S-Video, HD.
Auto Picture button
Press repeatedly to select either Personal, Rich,
Natural, Soft, or Multimedia picture setting.
Surf Button
Press to select previously viewed channels. You can
place up to 8 channels in memory. Then by
pressing the SURF button you can quickly view the
select channels.
3
ANTENNA TV
A combination antenna receives normal broadcast channels (VHF 2–13 and UHF 14–69). Your connection is easy because there is only
one 75 Ω (ohm) antenna jack on the side of your TV, and that’s where the antenna goes.
If your antenna has a round cable (75 ohm) on the end, then
you’re ready to connect it to the LCD TV. If your antenna
has flat, twin-lead wire (300 ohm), you first need to attach
the antenna wires to the screws on a 300- to 75-ohm
1
TV
adapter(not supplied).
Connect the antenna (or adapter) to one end of the
supplied L-Adapter as shown, and connect the other end of
the L-Adapter to the TV jack on the side of the LCD TV.
2
Plug the DC adapter into the DC IN 16V jack on the LCD
TV. Plug the power cable into an outlet and switch TV set on.
3
4
DVI-I IN
AUDIO IN
DC IN
16V
DVI (HDCP / PC ANALOG)
Run the AUTO PROGRAM function to set up the TV for the
broadcast or cable channels available in your area. If you do
not run the auto program function to set up the channels ,
your television may not operate properly.
3
Outdoor or Indoor Antenna
(Combination VHF/UHF)
Television
DC Adapter
2
Twin-lead
wire to
300-75Ω
adapter
Power
Cable
1
HELPFUL HINT
• Remember, an antenna or cable TV signal must first be connected to
your LCD TV.
OR
Antenna
with 75 Ω
cable
• Please make sure that you have selected the TV mode with AV+ key
on your remote control, before installing TV channels.
BASIC CABLE TV CONNECTION
Your Cable TV input into your home may be a single (75 ohm) cable or use a cable box decoder. In either case the connection is very
simple. Follow the steps below to connect your cable signal to your new television.
Direct cable connections:
The Cable TV signal from
Cable Company
Ω
(75 coaxial cable)
Connect the Cable TV signal to one end of the supplied
L-Adapter as shown, and connect the other end of the
adapter to the TV jack on the LCD TV.
L Adapter
1
TV
Plug the DC adapter into the DC IN 16V jack on the LCD
TV. Plug the power cable into an outlet and switch TV set on.
2
3
1
Run the AUTO PROGRAM function to set up the TV for the
broadcast or cable channels available in your area. If you do
not run the auto program function to set up the channels ,
your television may not operate properly.
DVI-I IN
AUDIO IN
DC IN
16V
DVI (HDCP / PC ANALOG)
HELPFUL HINT
• Remember, an antenna or cable TV signal must first be connected to
your LCD TV.
2
Power Cable
• Please make sure that you have selected the TV mode with AV+ key
on your remote control, before installing TV channels.
4
TUNER MODE CONTROL
The Tuner Mode allows you to change the LCD TV’s signal input to Cable or Air
(antenna). It’s important for the LCD TV to know if you want to receive channels from a cable TV signal or an antenna signal.
Press the MENU button to see the onscreen menu.
MAIN CONTROLS
1
PICTURE
AUDIO
LANGUAGE
TUNER MODE
INSTALL
FEATURES
AUTO PROGRAM
CHANNEL EDIT
MANUAL FINE TUNE
FACTORY RESET
ANTENNA
CABLE
AUTO
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
MANUAL FINE TUNE
FACTORY RESET
Press the CURSOR DOWN button to highlight the INSTALL menu.
Press the CURSOR RIGHT button to enter the INSTALL menu.
INSTALL
2
3
4
5
1
6
Press the CURSOR DOWN button to highlight the TUNER MODE menu,
then press CURSOR RIGHT to confirm.
�
�
�
�
4
5
Press the CURSOR DOWN button to select CABLE, ANTENNA
or AUTO, then press CURSOR RIGHT to confirm.
Press the MENU button repeatedly to clear the menu from the screen.
6
HELPFUL HINT
• When CABLE is selected, channels 2-125 are available.
• When ANTENNA is selected, channels 2-69 are available.
• When AUTO is selected, your LCD TV will search automatically for antenna
or cable channels.
• Immediately after unpacking and plugging in your new television, run the AUTO
PROGRAM function to set up the TV for the broadcast or cable channels
available in your area. If you do not run the auto program function to set up the
channels, your television may not operate properly.
AUTO PROGRAM (SETTING UP CHANNELS)
Your LCD TV can automatically set itself for local area (or cable TV) channels. This makes it easy for you to select only the TV stations in
your area by pressing the CH+ or CH- button.
Press the MENU button on the remote control to show the
1
2
3
4
5
6
MAIN CONTROLS
onscreen menu.
PICTURE
AUDIO
LANGUAGE
TUNER MODE
FEATURES
Press the CURSOR DOWN button to
highlight the INSTALL menu.
AUTO PROGRAM
CHANNEL EDIT
MANUAL FINE TUNE
FACTORY RESET
INSTALL
Press the CURSOR RIGHT button
to enter the INSTALL menu.
INSTALL
ANTENNA
CABLE
AUTO
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
MANUAL FINE TUNE
FACTORY RESET
Press the CURSOR DOWN button to
highlight the AUTO PROGRAM control.
Press the CURSOR RIGHT button to start the AUTO PROGRAM scanning
of channels.
INSTALL
LANGUAGE
TUNER MODE
Press the MENU button repeatedly to clear the menu from the screen, after
AUTO STORE has finished.
AUTO PROGRAM
CHANNEL EDIT
MANUAL FINE TUNE
FACTORY RESET
START?
HELPFUL HINT
AUTO STORE
• Immediately after unpacking and plugging in your new television, run the auto
program function to set up the TV for the broadcast or cable channels available in
your area. If you do not run the auto program function to set up the channels ,
your television may not operate properly.
PLEASE WAIT
PROG.FOUND
CHANNEL
0
3
• After you’ve run Auto Program, check out the results. Press the CURSOR DOWN
or the CURSOR UP button and see which channels you can select.
• Remember, an antenna or cable TV signal must first be connected to your LCD TV.
5
CABLE BOX (WITH RF IN / OUTPUTS):
Connect the Cable TV signal to the IN jack (or RF IN or CABLE
IN) on the Cable Box.
1
2
3
3
L-Adapter
TV
Connect an RF coaxial cable (not supplied) to the OUT jack (or
TO TV or RF OUT) of the Cable Box.
Connect the other end of the coaxial cable to one end of the
supplied L-Adapter as shown, and connect the other end of the
adapter to the TV jack on the LCD TV.
75
Ω
Coaxial
Cable
Plug the DC adapter into the DC IN 16V jack on the LCD TV.
Plug the power cable into an outlet and switch TV set on.
DVI-I IN
AUDIO IN
DC IN
16V
4
5
DVI (HDCP / PC ANALOG)
Set the Channel 3/4 (or Output channel) switch of the Cable Box
to 3 or 4. Set the TV to the same channel. When watching TV
programming, change channels at the Cable Box, not the LCD TV.
4
The Cable TV signal from
the Cable Company
DC Adapter
5
2
1
OUTPUT
CH
HELPFUL HINT
Power
Cable
3
4
CABLE
IN
TO TV
• Immediately after unpacking and plugging in your new television,
run the auto program function to set up the TV for the broadcast
or cable channels available in your area. If you do not run the auto
program function to set up the channels , your television may not
operate properly.
• Please make sure that you have selected the TV mode with AV+ key
on your remote control, before installing TV channels.
CABLE BOX (WITH AUDIO /VIDEO OUTPUTS):
This connection will supply stereo sound to the LCD TV.
Connect the Cable TV signal to the IN jack (or RF IN or CABLE
IN) on the Cable Box.
TV
1
2
Using an RCA-type video cable (not supplied) connect one end of
the video cable to the Video Out jack of the Cable Box. Connect
the other end of the cable to the yellow VIDEO jack on the side
of the TV. Video cables are usually marked with yellow and are
available from Philips or electronics retailers. Video jacks on most
equipment are yellow.
S-VIDEO
DVI-I IN
AUDIO IN
DC IN
16V
R
DVI (HDCP / PC ANALOG)
AUDIO
IN
Using RCA-type, stereo audio cables (not supplied), connect one
end of the cables to the left and right Audio Out jacks of the Cable
Box. Connect the other end of that cable to the Audio jack on the
side of the LCD TV. Audio cables are usually marked with red and
white and are available from Philips or electronics retailers. The
right audio jack is red and the left audio jack is white. Match the
cable colors to the jack colors.
4
1
3
L
3
DC Adapter
VIDEO
IN
Audio Cable
Power
Cable
2
Cable
TV signal
Plug the DC adapter into the DC IN 16V jack on the LCD TV.
Plug the power cable into an outlet and switch TV set on.
Video Cable
4
Note: Use the AV+ button on the remote control to tune to the AV
channel for the cable box signal. Once tuned, change channels at the cable
box, not the television.
When you watch programs using VCR, it’s recommended to select Soft
Mode via Auto picture.
OUTPUT
CH
3
4
L
R
CABLE
IN
TO
TV
AUDIO
OUT
VIDEO
OUT
Cable Box
6
S-VIDEO CONNECTIONS
The S-Video connection on the rear of the LCD TV can provide you
with better picture detail and clarity for the playback of accessory
sources such as DBS (digital broadcast satellite), DVD (digital video
discs), video games, and VHS VCR (video cassette recorder) tapes
than the normal antenna picture connections.
TV
S-VIDEO
Connect an S-Video cable to the S-VIDEO jack of the other
equipment (DVD Player, Camcorder, etc.) and to the S-VIDEO jack
on the rear of the LCD TV.
1
R
AUDIO
IN
DVI-I IN
AUDIO IN
DC IN
16V
L
Connect RCA-style audio cables (usually red and white) to the
AUDIO OUT (left and right) jacks on the other equipment.
Connect the other end of the cables to the AUDIO jack on the
side of the LCD TV.
DVI (HDCP / PC ANALOG)
2
3
VIDEO
IN
Power Cable
2
Plug the DC Adapter into the DC IN 16V jack on the LCD TV.
Audio Cable
1
3
Plug the power cable into an outlet. Turn on the LCD TV and other
equipment.
S-Video
Cable
OUT
AUDIO
IN
OUT
S
-VHS OUT
Press the AV+ buttons to set the LCD TV to its S-VIDEO mode.
ANTE NNA
IN
VIDE
O
R
L
4
5
ANTE NNA
OUT
IN
Press PLAY on the other equipment to view its material on the
LCD TV.
VCR or External
Accessory Device
(with S-Video
Output)
4
Note:
• The Philips LCD TV remote control can not be used to operate other video/audio
equipment.
• The Audio jack of AV IN is shared between Video (CVBS) and S-Video signals. If Audio
and Video is connected to S-Video input, you can still hear sound if you select Video via
AV select, even there appears no image on screen.
5
3
COMPONENT (HD) CONNECTIONS
Component Video input provide the highest possible color and
picture resolution in the playback of digital signal source material,
such as with DVD players. If you are using a HD (High Definition)
receiver that can transmit high definition programming, the TV can
accept those signals through the Component input located on the
bottom of the TV.
Connect the component (Y, Pb, Pr) Video OUT jacks from the
DVD player (or similar device) to the COMP(onent) VIDEO Input
jacks on the bottom of the LCD TV.
DVI-I IN
AUDIO IN
DC IN
16V
Y
Pb
Pr
L
R
1
COMPONENT VIDEO
AUDIO IN
DVI (HDCP
/
PC ANALOG)
COMPONENT HD/SD
COMPONENT
V IDEOCABLES
(Green, Blue, Red)
2
3
Audio Cable
Connect the red and white AUDIO CABLES to the Audio (left
and right) output jacks on the rear of the accessory device to the
AUDIO IN jack. Connect the other end of the cable to the Audio
jack on the rear of LCD TV.
Power Cable
2
Plug the DC Adapter into the DC IN 16 V jack on the LCD TV.
Plug the power cable into an outlet. Turn on the LCD TV and other
equipment.
1
3
2
COMPV IDEO
Pb
S-V IDEO V IDEO AUDIO
R
Y
OUT
OUT
OUT
Press the AV+ button on the remote control to select HD. HD will
appear in the upper left corner on the TV screen.
L
Pr
4
3
4
Insert a DVD disc into the DVD player and press the PLAY button
on the DVD Player.
5
5
ACCESSORY DEVICE
EQUIPPED WITH COMPONENT
VIDEO OUTPUTS.
Note:
• The Philips LCD TV remote control can not be used to operate
other video/audio equipment.
7
PC (MONITOR) INPUTS:
This LCD TV can be used as a PC. Your computer will have to be
equipped with a VGA type video output and interface cable (not
supplied). (One end with VGA type connector, the other end with
DVI-I type connector.)
Connect VGA end of the interface cable (not supplied) to the
computer, while connecting the other ends to the DVI INPUT jack
on the LCD TV.
1
2
Although audio connections are not required, the LCD TV can
reproduce the computers audio out by an AUDIO ADAPTER to
the Audio output jack on the computer (if available) while
connecting the other ends of the Audio cables to the PC AUDIO
Jacks on the bottom of the TV.
�
DVI-I IN
AUDIO IN
DC IN
16V
DVI (HDCP / PC ANALOG)
3
4
Plug the DC Adapter into the DC IN 16V jack on the LCD TV. Plug
the power cable into an outlet. Turn on the LCD TV and PC.
�
�
�
Press the AV+ button until PC MODE appears on the screen.
Audio Cable
DVI
Cable
Power Cable
�
HELPFUL HINT
• For PC function, it just accepts analog input via DVI-I type connector.
�
Computer
8
|