P E A V E Y E L E C T R O N I C S
SPECS
SP™ 2X
SPECIFICATIONS
Frequency response, 1 meter
on-axis, swept-sine in anechoic
environment:
53 Hz — 16 kHz ( 3 dB)
Usable low frequency limit
(-10 dB point):
44 Hz
Power handling:
Full Range:
500 W continuous
1,000 W program
2,000 W peak
Low Frequency Section:
500 W continuous
1,000 W program
2,000 W peak
High Frequency Section:
60 W continuous
120 W program
240 W peak
Sound pressure level, 1 Watt,
1 meter in anechoic environment:
Full Range:
98.0 dB SPL, (2.83 V input)
Low Frequency Section:
99.0 dB SPL, (2.83 V input)
High Frequency Section:
107.0 dB SPL, (2.83 V input)
High Frequency Section:
Crossover frequency (internal
passive):
1x .875 in. exit/51 mm voice coil
compression driver on CD horn
Rx22™ on a CH®-941
Low Frequency — High Frequency:
1,600 Hz
Box tuning frequency:
Low Frequency Section:
53 Hz
Recommended active crossover
frequency region and slope:
Low Frequency — High Frequency:
1,600 Hz at 18 dB/octave
Maximum sound pressure level
(1 meter):
Full Range:
125.0 dB SPL continuous
131.0 dB SPL peak
Low Frequency Section:
126.0 dB SPL continuous
132.0 dB SPL peak
Harmonic distortion:
1% rated power
2nd Harmonic:
Time offset:
Low frequency:
High frequency:
0.00 ms
0.65 ms
100 Hz:
1 kHz:
1.62%
0.22%
Impedance (Z):
Full Range:
Nominal:
3rd Harmonic:
100 Hz:
1 kHz:
0.52%
0.63%
8.0 Ω
7.2 Ω
Minimum:
10% rated power
2nd Harmonic:
High Frequency Section:
124.8 dB SPL continuous
130.8 dB SPL peak
Low Frequency:
Nominal:
Minimum:
8.0 Ω
6.1 Ω
100 Hz:
1 kHz:
5.09%
0.81%
Transducer complement:
Low Frequency Section:
1x 15 in. woofer, vented
1508-8 HE BWX
High Frequency:
Nominal:
Minimum:
3rd Harmonic:
100 Hz:
1 kHz:
8.0 Ω
6.0 Ω
1.97%
0.92%
upon having a minimum of 3 dB of
amplifier headroom available.
This product is manufactured under U.S.
Patent 6,064,745.
Architectural and Engineering
Specifications
The loudspeaker system shall have an
operating bandwidth of 53 Hz — 16 kHz.
The nominal output level shall be 98.0 dB
when measured at a distance of one
meter with an input of one Watt. The
nominal impedance shall be 8.0 Ohms.
The maximum continuous power handling
shall be 500 Watts, maximum program
power of 1,000 Watts and a peak power
input of at least 2,000 Watts, with a
minimum amplifier headroom of 3 dB.
The nominal radiation geometry shall be
90 degrees in the horizontal plane and
40 degrees in the vertical plane. The
outside dimensions shall be 33.25 inches
high by 21.00 inches wide by 22.75 inches
deep. The weight shall be 85 pounds.
The loudspeaker system shall be a
Peavey model SP 2X.
Harmonic Distortion
3 + 2 YEAR LIMITED WARRANTY
NOTE: For details, refer to the
warranty statement. Copies of
this statement may be obtained
by contacting Peavey Electronics
Corporation, P.O. Box 2898, Meridian,
Mississippi 39301-2898.
Second and third harmonic distortions vs.
frequency are plotted in figures 3 and 4 for
two power levels. Ten percent (10%) of
rated input power and either one percent
(1%) of rated input power or one Watt,
whichever is greater. Distortion is read
from the graph as the difference between
the fundamental signal (frequency
response) and the desired harmonic. As
an example, a distortion curve that is
down 40 dB from the fundamental is
equivalent to 1% distortion.
Mounting
Warning: This unit is not designed for
overhead suspension. SA™ 1 stand
adpater is included on the bottom for
stand mounting applications.
Harmonic Distortion : 10% Rated Power
120
110
100
90
80
70
60
50
20
50
100
200
500
1k
2k
5k
10k
20k
Frequency (Hz)
2nd Harmonic
3rd Harmonic
Figure 3
Harmonic Distortion : 1% Rated Power
110
100
90
80
70
60
50
40
20
50
100
200
500
1k
2k
5k
10k
20k
Frequency (Hz)
2nd Harmonic
3rd Harmonic
Figure 4
SP™ 2X INPUT
Features and specifications subject to change without notice.
Peavey Electronics Corporation • 711 A Street • Meridian • MS • 39301
©2001
Printed in the U.S.A. 3/01
|